ODROID-H2 双网口HTPC

By | 2019年10月10日

Key Features

  • Intel Quad-core processor J4105 (14nm) with 4MiB Cache, up to 2.5Ghz(Single Thread) or 2.3Ghz(Multi Thread)
  • Dual-channel Memory DDR4-PC19200 (2400MT/s)
  • Total 32GiB RAM Space with two SO-DIMM slots
  • 4 x PCIe 2.0 for one M.2 NVMe storage
  • 2 x Gbit Ethernet ports
  • 2 x SATA 3.0
  • SSE4.2 accelerator (SMM, FPU, NX, MMX, SSE, SSE2, SSE3, SSSE3, SSE4.1, SSE4.2, AES)
  • Intel UHD Graphics 600 (Gen9.5 LP GT1) up to 700Mhz
  • HDMI 2.0 and DP 1.2 multiple 4K/60Hz video outputs
  • RTC / BIOS backup battery is included

From June 2019, Rev-B board will be shipped. The improvements are as below; 

– CLK-REQ signal pull resistor is added to support a PCIe-to-SATA bridge board
– 12V SATA power source improvement for high power HDDs.
– Add a M.2 screw for NVMe storage installation
– Preinstalled the latest BIOS 1.05.
– more detail to WiKi https://wiki.odroid.com/odroid-h2/hardware#odroid-h2_schematics

Specifications

Form Factor

(体积重量)

  • Dimensions: 110mm x 110mm x 47mm
  • Weight: 285 g including heatsink

Processor

(中央处理器)

  • Intel Celeron J4105 Processor (14nm, TDP 10W)
  • Up to 2.5Ghz(Single Thread) or 2.3Ghz(Multi Thread)
  • 4MB L2 Cache
  • UHD Graphics 600 (Gen 9.5 LP GT1 up to 700MHz)
  • Fan-less design

Memory

(内存)

  • 2 x DDR4 1.2V SO-DIMM slots
  • Dual Channel, up to 2400 MT/s (DDR4-PC19200)
  • Max memory capacity 32GB
    • DDR3 is not supported

Storage

(存储)

  • 1 x eMMC connector (bootable and selectable on BIOS)
    • Various eMMC modules can be purchased at Hardkernel store
  • 2 x SATA3 6Gbps
  • 1 x M.2 NVMe slot (PCIe 2.0 x 4, supports NGFF-2280 cards)
    • M.2 SATA SSD is not supported

Networking

(网络)

  • 2 x GbE LAN ports (RJ45, supports 10/100/1000 Mbps)
  • Realtek RTL8111G
  • Supports Wake-On-Lan
  • LED indicators (Green: Link, Amber: Traffic)

Video

(视频)

Audio

(声音)

  • 1 x Audio out (3.5mm jack)
  • 1 x Audio in (3.5mm jack)
  • 1 x SPDIF out (ALC662, HDA codec)

External I/O

(扩展I/O)

  • 2 x USB 3.0 Host ports
  • 2 x USB 2.0 Host ports
  • 1 x Peripheral Expansion Header (20-pin, 2.54mm pitch)
    • 1 x DC 5V, 1 x DC 3.3V, 5 x GND
    • 2 x UART (TXD/RXD/RTS/CTS)
    • 2 x I2C (SCL/SDA)
    • 1 x External Power Button
    • All 3.3V I/O signal level
Other features
  • Passive Heatsink
  • BIOS Backup Battery
    •  Maintains system time and BIOS settings
  • Power Button
  • Reset Button
  • System LEDS Indicators:
    •  Red (PWR) – Solid light when DC power is supplied
    •  Blue (left, ALIVE) – Solid light when System is running
    •  Blue (right, RESET) – When the RESET button is pressed
    •  Amber (SATA) – Flashes when there is data transfer
    •  Green (NVMe) – Flashes when there is data transfer
  • Active Cooling Fan Connector (5V 4-pin, PWM input + TACHO output)
    • Active Cooling Fan is optional
    • Connector (4-pin, 1.25mm pitch)

Power

(电源)

  • 1 x DC jack : outer (negative) diameter 5.5mm, inner(positive) diameter 2.1mm
  • DC 14V ~ 20V (up to 60W)
    • DC 15V/4A power adaptor is recommended
  • Power consumption:
    •  IDLE : ≃4W
    •  CPU Stress : ≃14W
    •  CPU+GPU Stress : ≃22W
    •  Power-off : ≃0.5W
    •  Suspend : ≃0.6W

发表评论

电子邮件地址不会被公开。 必填项已用*标注